New Models & Products
NEW MODELS & PRODUCTS
GIFT PACK
Take-along spray cans of Petrochem Instant Starting Fluid and Foaming Hand Klean are now offered in a gift pack for motorcycle owners by Ashland Chemical Co. The starting fluid, when sprayed into carburetor or airstream, enables the engine to fire immediately, even in cold, wet weather, saving batteries and ignition systems. The hand cleaner sprays on, needs no water, and gets rid of grease, grit and grime. The pack sells for about $3 at motorcycle dealers. Additional information may be obtained from Ashland Chemical Company, Specialty Products Division, Dept. CW-5, 10505 S. Painter Ave., Santa Fe Springs, CA 90270.
HODAKA REED INDUCTION
If you are planning to use Pabatco’s reed induction on your 100-cc Hodaka, D.H. Enterprises offers machine shop service to modify the cylinder specifically for the Pabatco reed. This applies only to the 100-cc engine, as the 90-cc machines have too small a bore size.
Part of the procedure is to carefully enlarge the inlet on the rear of the Hodaka racing cylinder in a milling machine to mate with the reed manifold. The work is done accurately.
The pair of auxiliary transfer passages on the rear of the cylinder are also added without chance for error. The 7/16-in.-wide ports are not ground into the barrel; they are machined in, using a milling machine. Each port is formed by overlapping a pair of cuts, giving a gentle port shape which does not interfere with proper piston ring action. The operation gives precise control of port height, width, and angle. Because of the special porting requirements on the rear of the cylinder, modified cylinders with “five-port grooves” should not be sent.
Note that these modifications are classified as a machine shop service, not a porting service. The completed cylinders will be straight from the milling machine, and will not be finished by hand. The work will be dimensionally correct, and can be run as is, or cleaned up by hand for that finishing touch.
The standard 100-cc ACE barrels (part number 922505) can also be modified to accept the reed. Extra work is required, as a larger gasket surface must be created by milling into the rear of the cylinder. Much work is also required to shape the small inlet passage to the size dictated by the reed manifold.
Price for modifying the ACE 100 racing cylinder (PN 932505) or the Super Rat cylinder (PN 932511) is $16. The standard ACE 100 cylinder can be modified for $22. The piston for any of these engines can also be modified to suit the requirement of the reed valve for $6 each.
Send your prepaid order, including return postage, to DH Enterprises, Dept. CW-5, 1605 Lynngrove Dr., Manhattan Beach, CA 90266.
IMPORTED GOGGLES
These lined goggles, featuring contoured, precision triplex lenses for eye safety with maximum visibility, are now being offered by Suzuki Fun Center. Thick foam padding under simulated leather frame liners and a floating bridge ensure comfort. The lenses are tightfitted into steel frames which are held in place by special removable clips so the goggles will fit all types of helmets, including full-coverage. The goggles are available for $5.95 from Suzuki Fun Center, Dept. CW-5, 515 N. Victory Blvd., Burbank, CA 91502.
(Continued on page 114)
Continued from page 112
ELECTRONIC IGNITION
Cycle/See/Dee is an electronic ignition system designed specifically for motorcycles and provides positive ignition at all speeds and under full load. The system has the ability to fire fouled plugs and keep the engine in tune. The one standard model can be installed on 6-volt, 12-volt, one-cylinder, two-cylinder or four-cylinder engines using a standard negative ground battery. The unit is available for $24.95 from Judson Research and Mfg. Co., Dept. CW-5, Conshohocken, PA 19428.
COFFIN-STYLE TANK
This coffin-style gas tank, specifically designed for the Honda 750, Harley 74, and Kawasaki 500, will mount easily on any big-bore motorcycle. It comes with a full-color paisley bottom, twist-off gas cap, and two molded-in petcock fittings. It also is available in a flat bottom and 1-, 2or 3-in. tunnel models. The price is $49.95 from The Fiberglas Works, 2600 Soquel Ave., Dept. CW-5, Santa Cruz, CA 95060.
HIGH-PERFORMANCE SUZUKI CYLINDER HEAD
Webco’s two new high performance cylinder heads are available for Suzuki 125s and 185s. Benefits gained from the aluminum heads are a significant power increase and reduced engine temperatures throughout the entire operation range. Accurate machining assures a good fit. Both the 125 and the 185 heads use a 1/2-in.-reach spark plug, and are finished in competition black. Webco part number for the 125 Suzuki head is 2261; for the 185 head, part number is 2262. Both are priced at $39.95 and are available from Webco dealers throughout the U.S.
ANCRA TIE DOWNS
Ancra Corp. now is offering its aircraft quality tie downs to motorcyclists. The 6-ft. straps are 1-in. wide nylon webbing. Each end has a vinyl-dipped hook for easy, no-scratch connections. A cam-operated aluminum buckle is claimed to make the tie down foolproof. The weatherproof, snagproof tie downs are available at local dealers or from Ancra Corp., Dept. CW-5, P.O. Box 891, El Segundo, CA 90245, for $8.95 plus 75 cents postage.
(Continued on page 116)
Continued from page 114
TOP GEAR RIDING SUIT
Top Gear’s two-piece riding suit of tough nylon is available to stave off the discomfort of inclement weather. Flexible tailoring allows easy movement and room for extra clothing underneath. The jacket has big, quick-snap pockets and a quick-snap front over the heavy-duty zipper. Velcro fasteners assure air-tight collar and ankles, the jacket belt cinches tight to prevent cold air from blowing up, the wrists have knitted cuffs, and the trousers have an elastic waistband. Choice of colors includes red, black, aqua, orange, or navy. Available for $29.95 from your bike dealer or Top Gear Accessories, Dept. CW-5, 80 Pompton ave., Verona, NJ 07044.
QUIET POWER
A new dyno-tested Kawasaki 175cc F7 Enduro pipe is said to increase bhp throughout all rpm ranges, yet eliminate excessive exhaust noise. The lightweight pipe features a built-in glass pack silencer and bolts on in minutes. All hardware is included. The pipe retails for $45. For additional information, contact Bassani Manufacturing, 1117 Fountain Way, Dept. CW-5, Anaheim, CA 92806.
(Continued on page 118)
Continued from page 116
KAWASAKI CYLINDER HEADS
Webco has developed cylinder heads for the F-6 and F-7 (125cc and 175cc Kawasaki) which are cast from prime grade aluminum and feature precision machine work throughout. The heads utilize a 1/2-in. reach sparkplug and include a cast-in boss for a compression release. Part number for the 125cchead is 2192 and for the 175 cc is 2201. Both heads sell for $39.95 and are available through motorcycle dealers.
CUSTOM VALVE COVERS
Honda 750cc and 500cc custom valve covers now are available from Racecrafters International. The lightweight covers are said to be precision machined from top quality aluminum and are highly polished and finned for maximum heat dissipation. A set of four covers retails for $9.95 or the complete set of eight covers for $17.95 from Racecrafters International, Box 347, Dept. CW-5, Los Angeles, CA 90028.
(Continued on page 120)
Continued from page 118
VETTER WINDJAMMER
For fairing-minded BMW and Honda 500 owners, Vetter has designed the Windjammer, complete, among other things, with a 50-watt sealed beam headlight.
“Other things” include a double-wall fiberglass construction with a gel-coated finish; turn signal ports; a mounting step for the optional lower portion, which makes it a full-coverage fairing; two side storage compartments for the cockpitlike interior; a clear, Plexiglass windshield; a leather-grained motif and vinyl trim; and all necessary mounting hardware including a complete wiring harness. Price of the white fairing is $150; a black fairing is available for $157.50.
For optional equipment, Vetter offers the aforementioned lower portion; a tinted windshield for $6, available in Smoke but not recommended for night driving; a graphics package to give your bike a customized look (specify the color of your bike); snap vents located in the shield which pop open for rider comfort at $10.50 factory installed or $9.25 in kit; and a tonneau cover set of naugahyde to snap over the storage compartment openings, priced at $9.50 factory installed or $9.00 in kit.
Direct orders and queries to Vetter Fairing Co., Dept. CW-5, P.O. Box 927, Rantoul, IL 61866.
